Why can’t my camera connect or show up on the network?
Troubleshoot This Issue
If your camera cannot connect or appear on the network, the issue may be related to physical connection status, conflicting network settings, or service configuration:
1. Check Physical Connection and Indicator Status: Check the NVR or device indicator lights; the Network status indicator light (NET) being lit (usually blue or red, depending on the model) indicates that the network connection is abnormal.
2. Verify Network Connectivity: Use a computer on the local network to check the connection status of the device using the “ping …” command.
3. Check/Modify IP Address and Gateway: Ensure the camera’s IP address and default gateway must be on the same network segment as the NVR. Modify the IP address settings via the network configuration pages if necessary.
4. Address IP/MAC Conflicts: Check the system logs or network configuration to determine if there is an IP address conflict or MAC address conflict and resolve them.
5. Enable ARP/Ping Service (for IP Modification): If you are attempting to configure the camera’s IP address using the ARP/Ping command, verify that the “Enable ARP/Ping to set IP address service” function is enabled.
6. Resolve NVR Reboot Network Issues: If the network connection was accessible initially but lost after the NVR rebooted, leading to changes in the subnet mask or gateway, you should upgrade the applications and reconfigure the settings.
Why won’t my NVR add the camera, even though it’s powered on?
If the camera is online but the NVR fails to register it, check these areas:
• Camera Initialization Status: The camera must be initialized before being added to the NVR.
◦ If you connect a camera via a PoE port, the NVR usually initializes it automatically, but if the NVR was recently upgraded, it might fail to initialize the camera automatically, requiring manual initialization.
• Credentials and Network Details: The IPC IP address or port number may be incorrect, or the IPC account (username/password) may be wrong.
• IP Conflicts and Limits: The IPC IP might be in the blocklist, or the NVR might have reached its limit for connected devices (“the device has connected to the too many IPC”).
• Time Synchronization: Ensure the IPC port value and the time zone are the same as the NVR.
• Plug and Play Function: If the NVR’s Plug and Play function is enabled, the device automatically adds cameras on the same LAN and initializes uninitialized cameras before adding them. If a device added via Plug and Play was removed, it will be automatically added again if the feature remains enabled.
Troubleshoot This Issue
If the camera is functional but cannot be successfully added to the NVR, perform the following initialization and configuration checks:
1. Initialize the Camera (If New/Upgraded NVR): The camera must be initialized prior to adding it to the Device. If the camera is connected via a PoE port, the NVR usually initializes it automatically, but if the NVR was recently upgraded, you may need manual initialization.
◦ Initialization generally involves setting the login password, email address for resetting, and confirming IP settings.
2. Verify Camera Credentials and Port Information: Check if the IPC IP address or port number may be incorrect, or if the IPC account (username/password) may be wrong. If the camera is already listed as added but failing connection, use the Edit option on the Added Device list to verify the IP address, username, and password.
3. Check IP Blocklist and Connection Limits: Confirm that the IPC IP is not in the blocklist. If the error message indicates “the device has connected to the too many IPC,” the NVR has reached its connection capacity.
4. Synchronize Time Zone and Port Value: Ensure the IPC port value and the time zone is the same as the NVR.
5. Use Manual or Search Addition Methods:
◦ Search Method: Click Search Device on the Camera List page, then select the detected remote device and click Add.
◦ Manual Method: Click Manual Add and provide the necessary parameters like IP address, manufacturer, and credentials directly.
6. Check/Manage Plug and Play: If Plug and Play is enabled, the NVR automatically adds cameras on the same LAN and initializes new cameras. If a manually removed device keeps reappearing, this function may need to be disabled or adjusted.
Why isn’t the remote viewing app working or showing my cameras?
• Network Connectivity and Stability: Issues preventing remote access include a general network connection error, network setup error, or invalid password or username.
• P2P Configuration: For remote management using P2P functionality, the NVR must be connected to the WAN (Wide Area Network). If P2P registration is successful, the status should display as “Online”.
• Video Feed Issues: If the video displays “only mosaic, no video” when previewing or playing back remotely, the network fluency is not good or the client-end resources are limited.
• Camera Status: If the IPC is offline, you will naturally see no video.
Troubleshoot This Issue
Remote access failures often relate to networking configuration, P2P status, or client capacity:
1. Verify P2P Connectivity: Confirm that the NVR is connected to the WAN (Wide Area Network). On the P2P configuration page, check that the Status becomes Online after configuration.
2. Confirm Credentials: Check if the remote access issue is due to an invalid password or username.
3. Troubleshoot Network Errors (Web/Client): If you cannot log in via the client or web, check for network connection error or network setup error. Use the ping command to test connectivity.
4. Address Video Quality Issues (Remote Viewing): If the remote video shows “only mosaic, no video”, this indicates that the network fluency is not good or the client-end resources are limited. This may necessitate optimizing your network bandwidth or ensuring your client device meets the recommended hardware specifications (e.g., Quad Core, 2G or higher memory, 256M+ display card memory for 16-channel remote monitoring).
Why is the video blurry, pixelated, or lagging?
• Network Bandwidth and Resources:
◦ Low network fluency is a common cause for mosaic or low quality video when viewing remotely.
◦ Viewing multiple channels remotely requires sufficient network bandwidth (at least 100M or higher for multi-channel monitoring) and adequate PC resources (e.g., for 16-channel remote monitoring: Quad Core, 2G or higher memory, independent displayer with 256M+ display card memory).
• Encoding and Processing Issues:
◦ Video quality setup might be too low.
◦ A program read error where the bit data is too small can cause mosaic in the full screen; restarting the NVR may solve this problem.
• Camera Image Settings (IPC):
◦ Image clarity can be manually adjusted via camera parameters such as Brightness, Contrast, Sharpness, and Saturation.
◦ In foggy or hazy environments, utilizing the defog function can help improve image clarity.
◦ When the image is blurry due to lens vibration, camera functions like Optical Dejitering or EIS (Electronic Image Stabilization) can compensate for shaking.
Troubleshoot This Issue
Video degradation can be caused by physical factors, transmission issues, or coding errors:
1. Check for Coding/System Errors: If the video quality issue involves distorted recorded videos or mosaic in the full screen due to a program read error or bit data being too small, Restart the NVR to solve this problem.
2. Check Video Quality and Encoding Settings: Ensure the Video quality setup is not too low. Adjust encoding parameters like Compression, Resolution, Frame Rate (FPS), and Bit Rate (via Main Menu > Camera > Encode > Audio/Video).
3. Address Lens and Clarity Issues (Camera): Use the camera settings (accessible via NVR remote configuration or directly on the IPC web interface) to improve clarity:
◦ Adjust Brightness, Contrast, Sharpness, and Saturation.
◦ Utilize the defog function if operating in foggy/hazy environments (set Mode to Manual or Auto).
◦ If blurriness is caused by lens vibration, enable camera functions like EIS (Electronic Image Stabilization) or Optical Dejitering [ EIS: 725, Optical: 726, 2278, 2572].
4. Verify Display Resolution (Local View): If the video is displayed but not full on the monitor, check the current resolution setup. If necessary, shut down the device, reboot while pressing and holding the Fn button (or releasing after 5 seconds) to restore NVR resolution to the default setup.
Why isn’t my system recording, or why are recordings missing?
• Storage Device Issues:
◦ The problem could be caused by a damaged HDD or HDD ribbon, insufficient HDD capacity, or HDD malfunction.
◦ For local recordings on an IPC, potential exception alarms include Disk Full (free space less than configured limit), SD Card Error (failure or malfunction), or No SD Card.
• Recording Configuration and Status:
◦ The recording function may have been disabled.
◦ If the record mode is set to Auto, ensure the recording schedule (including type and time period) is correctly set.
◦ The “Disk Full” storage policy might be set to “Stop” instead of “Overwrite”.
• Data Loss During Disconnection (ANR): If the NVR loses connection with the camera and the camera supports ANR (Auto Network Resume), data recorded locally by the IPC during the outage will be downloaded later. However, this relies on the IPC having an SD card installed and the recording function enabled.
Troubleshoot This Issue
Recording problems are usually related to storage integrity, schedule configuration, or capacity limitations:
1. Check HDD Health: Investigate reasons for missing records, including a Damaged HDD or HDD ribbon. Check the HDD status indicator light (HDD) for immediate confirmation of HDD malfunctions.
◦ Run a Disk Check via Main Menu > STORAGE > Disk Check > Manual Check (selecting Key Area Detect or Global Detection) to monitor HDD status.
2. Verify Recording Status and Mode: Check that the recording function has not been disabled.
◦ Navigate to Main Menu > STORAGE > Record and ensure the Recording status is set to Auto (to follow the schedule) or Manual (for general continuous recording).
3. Confirm Recording Schedule: If the mode is “Auto,” verify that the desired time slots and record types (General, Motion, Alarm, etc.) are properly configured in the Recording Schedule via Main Menu > STORAGE > Schedule > Record.
4. Check/Adjust Storage Strategy (Overwrite Policy): If files are missing because they were overwritten, check the Disk Full storage strategy set in Main Menu > STORAGE > Basic is configured to Overwrite (or “Stop” if you prefer to stop recording when full).
5. Check ANR Configuration: If data is missing specifically due to NVR/IPC connection loss, verify that the IPC has an SD card installed and the recording function is enabled on the IPC, allowing the NVR to subsequently download the files (Auto Network Resume).
| Weight | 6 lbs |
|---|---|
| Highest Resolution | 8 Megapixel |
| NDAA Compliance | NDAA Compliant |
| Product Type | NVR |
| Recorder Channels | 4 Channel |
| Recorder Features | PoE |
| Series Compatibility | ARXIP Series |